2009/10/10

MOD205A Redboot Info

RedBoot> dumpflashboot

BDK#1 initialized
RedBoot> exec -l 0x80000 -b 0x800000
MMU and cache enabled
Start to run flGetPhysicalInfo
flGetPhysicalInfo done
Flash device type 0x00000000
Type of flash media 0x0000000F
Erasable size 0x00080000
Media size in bytes 0x10000000
Device interleaving 0x00000000
Start to read BDK partition...
BDK Read initialized
BDK Read Done...
Enable SATA I/O and memory space
Switch into AHCI native mode
Initialize SATA controller
Native mode, re-initialize memory space reg
Enable Port0 and Port1
CPUID: 69056854
B-step board
load_fpd
load_config_block
00000004
Video Output Port Switch: Up.
CPUID: 69056854
logoimage: 00080000 00060000
TV_MODE=00000003
inttvenc init
Ready to display splash screen...
total_copy_size=00340000
copy_unit=00006800

Load kernel...
Offset_kernel = 0x00120000
size_kernel = 0x00200000
real_size: 0017EB88

Load ramdisk...
Offset_ramdisk = 0x01000000
size_ramdisk = 0x00140000
real_size: 000D854F

Ready to boot Linux kernel ...
Kernel cmdline:
console=ttyS0,115200 mem=100M@0 root=/dev/ram0 init=/linuxrc
Flush the cache and disable cache

Boot Linux kernel now!
Uncompressing Linux.............................................................
......................................... done, booting the kernel.
Linux version 2.6.16.16 (root@rd) (gcc version 3.4.5) #14 PREEMPT Mon Jan 5 15:3
3:13 CST 2009
CPU: XScale3-monahans [69056854] revision 4 (ARMv5TE)
Machine: Intel OloCreek Development Platform
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 mem=100M@0 root=/dev/ram0 init=/linuxr
c
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 100MB = 100MB total
Memory: 96788KB available (2653K code, 530K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Checking timer frequency setting...
Timer Frequency 62500000 for (0xC44223CA, 0x2961C707)
olo_cf_init
checking if image is initramfs... no need to check
Freeing initrd memory: 1280K
NET: Registered protocol family 16
PCI: bus0: Fast back to back transfers disabled
olocreek_map_irq: Dev=1 Pin=1
olocreek_map_irq: Dev=2 Pin=1
olocreek_map_irq: Dev=3 Pin=1
olocreek_map_irq: Dev=23 Pin=1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xfffe0200 (irq = 29) is a Olo River with FIFOs enable
d.
serial8250: ttyS1 at MMIO 0xfffe0300 (irq = 29) is a Olo River with FIFOs enable
d.
RAMDISK driver initialized: 4 RAM disks of 49152K size 1024 blocksize
loop: loaded (max 8 devices)
sundance.c:v1.01+LK1.27 14-12-2006 Written by Donald Becker
http://www.scyld.com/network/sundance.html
eth0: IC Plus IP100A Fast Ethernet Adapter at 0xc6922000, 00:22:15:0c:66:82, IRQ
19.
eth0: MII PHY found at address 0, status 0x786d advertising 01e1.
ahci_init_one: enter
ahci_init_one: call pci_request_regions
cap 0x8101f01 port_map 0x3 n_ports 2
mmio c6924400 port_mmio c6924500
mmio c6924400 port_mmio c6924580
AHCI 0001.0000 32 slots 2 ports 1.5 Gbps 0x3 impl SATA mode
flags: stag
ata1: SATA max UDMA/133 cmd 0xC6924500 ctl 0x0 bmdma 0x0 irq 4
ata2: SATA max UDMA/133 cmd 0xC6924580 ctl 0x0 bmdma 0x0 irq 4
ata1: SATA link down (SStatus 0)
scsi0 : ahci
ata2: SATA link down (SStatus 0)
scsi1 : ahci
physmap flash device: 2000000 at c0000000
ehci_hcd 0000:00:03.0: EHCI Host Controller
ehci_hcd 0000:00:03.0: debug port 1
ehci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.0: irq 14, io mem 0xff820400
ehci_hcd 0000:00:03.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16 ehci_hcd
usb usb1: SerialNumber: 0000:00:03.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.3
uhci_hcd 0000:00:02.0: UHCI Host Controller
uhci_hcd 0000:00:02.0: detected 2 ports
uhci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:02.0: irq 13, io base 0xff810400
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16 uhci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new full speed USB device using ehci_hcd and address 3
usb 1-1.2: Product: EZ200PU Smart Card Reader
usb 1-1.2: Manufacturer: CASTLES
usb 1-1.2: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 100K
[+] Enter the /linuxrc
[+] Insert the MDOC Drivers
tffs: module license 'Proprietary' taints kernel.
tffs: TrueFFS driver 710.73
tffs: flSysfunInit: 0xC6928000 = 0x80803C02

tffs: ready(): ATA Error:
tffs: 0x4
tffs:
tffs:
io_input(): ATA not Ready (before data XFER)
tffs: rc = 0x4
tffs: DOCH found
tffsbd: no version for "tffs_get" found: kernel tainted.
tffsbd: TrueFFS block device driver 1
tffsbd: Registered module at major 100
tffsbdalo_cf_partition.
tffsbdblo_cf_partition.
tffsbdc: tffsbdc1 tffsbdc2 tffsbdc3 tffsbdc4 < tffsbdc5 tffsbdc6 tffsbdc7 >
[+] Mount the New Root
warning: file extends past end of filesystem
[+] Change to New Root
[+] Run the New Root Init
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on tffsbdc6, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
ESS SVEN init:Mar 4 2009 18:56:36
sven_driver.c: 291: SVEN Header Initialized c6968000@09948000:00001000, circbuf
d2a80000@09700000:00100000 dis:ffffffff
ESS OSAL release
Thu Apr 23 12:00:00 CST 2009
eth0 Link down, 7849.
eth0 Link down, 7849.
[896] Apr 23 12:00:02 Running in background
ARPING 10.157.63.254 from 10.157.50.250 eth0
eth0: Link changed: 100Mbps, full duplex.
Unicast reply from 10.157.63.254 [00:30:88:02:7E2] 18.396ms
Sent 9 probes (9 broadcast(s))
Received 1 response(s)
Connecting to 172.17.244.66[172.17.244.66]:8080
dynaconf.905 100% |*****************************| 639 00:00 ETA
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
Download file from 172.17.244.66
Begin load intel_smd drivers
eth0: Promiscuous mode enabled.
device eth0 left promiscuous mode
CAClient uses obsolete (PF_INET,SOCK_PACKET)
Begin to detect graphics chip type ...
Graphics chip type detected: Rock Spring!
Running @ 125MHz
Switch Up
Can't find smd buffer region
[map( 0xffb00000, 0x00080000 ) = 0x419a5000]
[map( 0xffb68000, 0x00080000 ) = 0x4314d000]
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hci_usb
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Can't get device info: No such device
281c8e36b4bde4e4d0f91f79a8d2e1c1 /mnt/browser/xfresco
GDL_PLANE_ID_GRAPHICS : w: 720, h: 480
cur version = MOD205.090512.01
Download file from 172.17.244.66
new version = MOD205.090512.01
Need not upgrade ...

MPEG-2 decoder registered with SMD (bf0a8840)

vtc_driver.c:vtc_driver_init:Initializing VTC built on Mar 9 2009 at 16:49:38,
debug level = 0, disp_fast = 0
YSS915 Karaoke Device Driver - 2009/04/01
After init_regs...
MDR (0x50), DAR (0x02), OPR (0xcb), TCR (0x00), RVR (0x00), KSR (0x00),
C01 (0x00), C02 (0x7f), C04 (0x00), C06 (0x7f), C09 (0x00), C0A (0x7f), C0E (0x
7f), C0F (0x00), C1E (0x65), C1F (0x65)
yss915_init done
turn on bit. result=0x00000004
Daemon start successful
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
eth0: Promiscuous mode enabled.
device eth0 left promiscuous mode
Download file from 172.17.244.66
Download file from 172.17.244.66
setup_document_default: http://apps.mod.cht
No log handling enabled - turning on stderr logging
NET-SNMP version 5.3.1 AgentX subagent connected
The PAT indicates 1 programs
Got PMT
There are 1 programs
There are 1 videos and 2 audios
audio information:
pid: 4130, type: 0x04
pid: 4132, type: 0x04

video information:
pid: 4131, type: 0x02
Unexpected callback call
Media detected!!
Switch to no capture...
We don't need video format information, format: MPEG2
No ADI memory configuration file detected.
Please switch to ADI configuration if you need to enable ADI/Software ADI
full redraw!!

1 則留言:

最新文章